This women's warm waterproof raincoat with hood is engineered for sustained performance in prolonged wet and cold conditions. It integrates a three-layer laminated shell with targeted insulation to maintain thermal efficiency while resisting water penetration under dynamic movement and variable wind exposure.

Designed for industrial, field, and municipal operations, the garment balances breathability with environmental protection to reduce heat stress and moisture accumulation during extended wear. Construction emphasizes seam integrity, hood adjustability, and closure reliability to minimize failure points in demanding use cases.

The outer shell uses a 100% polyester plain weave with a polyurethane (PU) coating rated for 10,000 mm hydrostatic head resistance, validated under ISO 811 test conditions. This layer provides primary water barrier function while maintaining flexibility down to -20°C.

A bonded microporous membrane (ePTFE equivalent) with 15,000 g/m²/24h moisture vapor transmission rate (MVTR) is laminated between the shell and inner liner, enabling sweat vapor escape without compromising waterproof integrity. The membrane is protected by a hydrophobic oleophobic treatment to resist oil and contaminant fouling.

Thermal insulation consists of 120 g/m² recycled polyester fiberfill, engineered with hollow-core filaments to trap air efficiently while retaining loft after repeated compression cycles. The fill weight is mapped to core body zones—torso and upper back receive full density, while sleeves and side panels use reduced fill to enhance mobility and reduce bulk.

The hood is constructed with a three-point adjustment system: vertical drawcord at the rear, lateral tensioners at the temples, and a stiffened brim with embedded wire to maintain profile in wind speeds up to 80 km/h. Hood volume accommodates hard hats or balaclavas without gaps that compromise precipitation runoff.

Front closure combines a water-repellent coil zipper with storm flap secured by magnetic snap closures at 80 mm intervals, reducing wicking paths while allowing rapid one-handed operation. Zipper teeth are coated with PTFE to resist corrosion from salt spray and industrial atmospheres.

Cuffs feature dual-adjustment hook-and-loop straps with laminated thermoset patches to prevent delamination, enabling glove-over wear while maintaining seal integrity. Hem drawcord uses bungee cord with cordlocks positioned at side seams to avoid snagging on equipment or vegetation.

Waterproofness is verified via spray test (ISO 105-E04) and hydrostatic pressure testing, with no leakage observed after 500 cycles of flexing at 30° bend angle. Breathability is measured using the inverted cup method (ASTM E96), confirming consistent MVTR across humidity gradients from 30% to 90% RH.

Thermal resistance (RCT) is rated at 0.35 m²·K/W under ISO 11092 conditions (5°C, 60% RH, 0.4 m/s air velocity), sufficient to maintain core temperature in -10°C ambient conditions with moderate activity. Dimensional stability after 5 wash cycles at 40°C shows <2% shrinkage in length and width, critical for fit consistency in PPE programs.

Abrasion resistance of the outer shell exceeds 20,000 cycles (Martindale, ISO 12947-2) before thread breakage, suitable for contact with rough surfaces, tools, and vegetation. Colorfastness to light (ISO 105-B02) maintains >4 grey scale rating after 40 UV hours, preventing premature fading in outdoor service.

This raincoat is specified for utility workers performing line maintenance in storm conditions, where prolonged exposure to rain and wind demands reliable moisture management without overheating. The hood’s compatibility with hard hats and the storm flap’s overlap design prevent water ingress at critical interfaces during overhead work.

In municipal sanitation and road maintenance teams, the garment’s resistance to oil-based contaminants and ease of decontamination support compliance with hygiene protocols. Reflective trim options (EN ISO 20471 Class 2) can be integrated into piping or panels for low-light visibility without adding bulk or stiffening the fabric.

Field service technicians in telecommunications and energy sectors benefit from the coat’s packability—when stored in the included stuff sack, it occupies <1.5 L volume—and rapid deployment design. The absence of internal mesh liners reduces snag points on tools and equipment belts, a common failure mode in traditional rainwear.

Shell color options include standard safety hues (high-visibility yellow, orange, red) and neutral tones (navy, charcoal, olive) with custom Pantone matching available for corporate identification. Reflective striping can be applied as circumferential bands on sleeves and torso or as segmented patches per client specification.

Insulation weight can be adjusted between 80 g/m² and 180 g/m² based on climate zone requirements, with corresponding adjustments to liner pocket depth to maintain drape and mobility. Hood dimensions—depth, width, and brim projection—are scalable to accommodate different headgear combinations or facial protection systems.

Closure systems can be modified to include waterproof zippers with welded storm flaps, magnetic closures only, or snap-over flaps for environments where metal components are restricted. Additional features such as interior document pockets, radio loops, or reinforced elbow patches are available as modular add-ons.

Each batch undergoes roll-to-roll inspection of the laminated shell for coating uniformity, delamination points, and pinhole defects using 10x magnification and UV fluorescence testing. Seam strength is validated via grab test (ASTM D5034) on taped seams, requiring minimum 20 N/50mm strength in warp and weft directions.

Insulation distribution is verified through thermal imaging during wear simulation, ensuring no cold spots exceed 3°C deviation from mean torso temperature. Final assembly includes functional testing of all closures, drawcords, and adjustability features under simulated load conditions.

Products are packaged in individual polyethylene bags with desiccant packs to prevent moisture retention during storage, then packed in cartons with corner protection and humidity indicators. Each unit includes a care label specifying wash temperature, tumble dry restrictions, and reproofing intervals to maintain performance lifecycle.

For technical inquiries, customization requests, or to request a sample kit with material swatches and construction details, contact our application engineering team.