Women's Fleece Waterproof Jacket

This jacket combines a waterproof outer shell with a bonded fleece lining to provide thermal insulation and moisture protection in wet, cold environments. Designed for industrial and outdoor work settings, it addresses the need for reliable personal protective equipment that maintains mobility while resisting precipitation and wind chill.

Material Construction and Layering

The outer layer consists of a 100% polyester ripstop fabric laminated with a polyurethane (PU) membrane, rated for 5,000 mm hydrostatic head resistance. This construction prevents liquid water penetration while allowing vapor transmission to reduce internal condensation. The inner layer is a 280 g/m² anti-pilling polyester fleece, thermally bonded to the shell to eliminate shifting and maintain consistent loft.

Seams are fully taped with waterproof tape using heat-activated adhesive, ensuring continuity of the moisture barrier at stitch points. The fleece lining is engineered to retain 85% of its insulating value when damp, based on standard ASTM D1518 thermal retention testing under controlled humidity conditions.

Design Features for Functional Performance

The jacket includes a storm flap over the front zipper, secured with hook-and-loop fasteners, to prevent water ingress through the zipper coil. Adjustable cuffs with internal gaiters and a drawcord hem allow sealing against wind and spray. A detachable hood with laminated brim and rear adjustment system provides head coverage without compromising peripheral vision.

Two hand-warmer pockets and one internal chest pocket are lined with fleece and feature water-resistant zippers with drainage grommets to prevent water accumulation. Reflective trim is integrated into the sleeves and back panel, meeting EN ISO 20471 Class 2 visibility requirements for low-light environments.

Sizing and Fit Considerations

The jacket is cut with a women’s-specific pattern, featuring tapered shoulders, contoured waist, and articulated elbows to accommodate layered clothing systems without restricting movement. Sizes range from XS to 3XL, with chest measurements graded in 2-inch increments. Sleeve length is proportionally scaled to torso size to prevent shortening during reach movements.

Layering compatibility is designed for a base layer and mid-layer insulation, with a recommended total system thickness not exceeding 25 mm under the shell to maintain breathability and avoid compression of the fleece loft. Users should consider activity level and ambient temperature when selecting layering combinations.

Applications in Industrial and Outdoor Work

This garment is suited for transportation, utility maintenance, construction site supervision, and cold-weather logistics operations where workers are exposed to rain, snow, or wind chill for extended periods. It is not intended for submerged conditions or high-heat environments, as the PU membrane begins to degrade above 80°C.

In forestry and agricultural settings, the quiet fabric reduces noise during movement, while the fleece lining provides sufficient warmth for stationary tasks such as equipment monitoring or surveying. The waterproof rating is sufficient for prolonged drizzle and light snow but may require additional rain gear in sustained downpours.

Quality Control and Manufacturing Consistency

Each batch undergoes hydrostatic head testing on a representative sample to verify waterproof performance, with acceptance criteria set at a minimum of 4,500 mm. Fleece weight and thermal resistance are checked via standardized fabric analysis, and seam integrity is validated through peel adhesion testing on taped joints.

Colorfastness is tested per AATCC 61 for laundering and AATCC 16 for light exposure to ensure visibility components retain reflectivity after repeated use. Dimensional stability is assessed after five wash cycles at 40°C, with shrinkage limited to 3% in both warp and weft directions to maintain fit over the garment’s service life.

Care Instructions and Longevity

Machine wash cold on gentle cycle, tumble dry low, or lay flat to dry. Do not use fabric softeners, bleach, or dry cleaning, as these can degrade the PU membrane and reduce waterproofing effectiveness. Reapply durable water repellent (DWR) treatment after 10–15 washes using a fluorocarbon-free spray-on product to maintain surface beading.

With proper care, the jacket maintains its waterproof and thermal performance for 12–18 months of regular use in moderate conditions. Abrasion resistance is rated at 15,000 cycles on the Martindale tester for the outer shell, sufficient for incidental contact with equipment and vegetation but not for continuous rugged terrain use.

For technical specifications, customization options such as logo placement, pocket configuration, or sizing adjustments, or to request a sample for evaluation, contact our product specialists. Provide details on intended use case, environmental conditions, and layering requirements to ensure appropriate recommendation.