A lightweight rain jacket designed for women combines waterproof performance with minimal packed volume, enabling rapid deployment during unexpected precipitation while maintaining freedom of movement in outdoor or field operations.

Packable construction relies on thin, high-tenacity nylon or polyester face fabrics laminated to microporous polyurethane membranes, achieving hydrostatic head ratings of 10,000 mm or higher while weighing less than 200 grams in size medium.

The jacket’s packability is quantified by its compressed volume—typically under 0.5 liters when stuffed into its internal pocket or included stuff sack—allowing storage in tool belts, backpacks, or vehicle compartments without sacrificing accessibility.

The outer layer uses 20D ripstop nylon with a density of 38 g/m², treated with a durable water repellent (DWR) finish rated to withstand 20+ wash cycles before reapplication is needed, based on AATCC Test Method 22.

Beneath the face fabric, a 0.012 mm microporous polyurethane membrane provides breathability, measured at 8,000 g/m²/24h moisture vapor transmission rate (MVTR) under JIS L 1099 B1 conditions, preventing internal condensation during aerobic activity.

Seams are sealed using 12 mm wide polyurethane tape applied via heat bonding at 140°C, achieving leak resistance equivalent to IPX6 standards when tested with a 100 L/min nozzle at 3 meters distance for 3 minutes.

The jacket features a three-panel hood with laminated brim and rear adjustment tabs, allowing vertical and circumferential tightening to maintain visibility during head movement without flapping in winds up to 25 km/h.

YKK AquaGuard® zippers with storm flaps protect front pockets and main closure; the coil elements are polyester with polyurethane coating, rated for 5,000+ cycles before functional degradation per ASTM D2061.

Articulated elbows and gusseted underarms increase range of motion by approximately 18% compared to flat-cut patterns, reducing fabric stress during reaching or lifting tasks common in maintenance or inspection workflows.

When packed, the jacket occupies a cylindrical volume of 9 cm diameter by 12 cm height, corresponding to 0.76 liters, measured using water displacement protocol after folding along manufacturer’s specified crease lines.

The integrated stuff sack uses the same 20D nylon as the shell, with a drawcord closure and bar-tacked stress points, adding only 12 grams to total system weight while enabling compression to 0.5 liters via manual rolling.

Weight distribution remains balanced when stored in a waist pack; the packed jacket’s center of gravity stays within 5 cm of the lumbar vertebra, minimizing torque during prolonged wear in dynamic environments.

Values represent averages from third-party testing of comparable products; actual performance depends on specific material lot, construction tolerances, and conditioning history.

Field technicians in telecommunications infrastructure use these jackets during tower inspections where sudden storms create slip hazards; the lightweight design prevents fatigue during prolonged climbs while maintaining dryness of underlying PPE layers.

In utility maintenance, crews deploying to substation sites value the jacket’s compatibility with high-visibility vests—its low profile allows wear underneath ANSI/ISEA 107-compliant outerwear without compromising reflective tape visibility or creating bulk that impedes movement in confined spaces.

Agricultural equipment operators benefit from the jacket’s resistance to dew and light rain during early-morning field checks; the breathable membrane prevents overheating during engine warm-up cycles, and the packed size fits within tractor cab storage compartments.

Face fabric denier can be adjusted between 15D and 30D based on abrasion resistance requirements; lower denier reduces packed volume but may decrease tear strength below 8 N (ASTM D2261), necessitating reinforcement in high-wear zones.

Membrane MVTR can be tailored from 5,000 to 15,000 g/m²/24h by altering pore density and polyurethane thickness, balancing breathability against hydrostatic head—higher MVTR typically correlates with reduced pressure resistance unless compensated by increased laminate thickness.

Color options are limited to solution-dyed polyester or nylon to maintain UV stability; standard colors include safety yellow (Pantone 803 C), navy (Pantone 654 C), and black, with custom Pantone matching available for orders exceeding 500 units.

For technical specifications, material data sheets, or to discuss application-specific adaptations, contact our engineering team.