Factory Direct Water Repellent Coat for Women

This product page details the technical specifications, material composition, and performance characteristics of a factory-direct water-repellent coat designed for women in industrial and outdoor work environments. The information focuses on measurable properties and functional design to support informed procurement decisions.

Material Composition and Treatment

The outer shell is constructed from a 240gsm nylon taffeta with a density of 180T, providing a balance of tear resistance (ASTM D2261) and flexibility. The water-repellent finish is achieved through a C6-based durable water repellent (DWR) treatment applied at 1.2 g/m², which maintains 80% effectiveness after 20 wash cycles per AATCC Test Method 135. The treatment does not form a membrane; instead, it lowers surface tension to cause water to bead and roll off at angles below 10°. The inner lining consists of 100% polyester mesh (120gsm) to facilitate moisture vapor transmission, with a RET value of <6 m²·Pa/W as measured by ISO 11092.

Design Features for Functional Performance

The coat features a center-front zipper with a storm flap secured by touch-and-close fasteners, reducing water ingress at the closure by approximately 70% compared to uncovered zippers (based on spray test equivalence). Adjustable hook-and-loop cuffs allow sealing against sleeves, minimizing water entry at the wrists. Two front pockets are positioned 15cm above the waistline to avoid interference with harnesses or belts, each with drainage holes (2mm diameter) spaced 25mm apart to prevent water accumulation. The back yoke includes a single pleat extending 8cm from the shoulder seam to improve mobility during overhead reaching without compromising the water-repellent integrity of the shoulder area.

Performance Testing and Validation

Water resistance is evaluated using ISO 811 hydrostatic pressure testing, where the fabric withstands 800mm H₂O before leakage occurs—sufficient for light rain and mist but not designed for sustained heavy precipitation or immersion. Breathability is assessed via upright cup method (ASTM E96), yielding a moisture vapor transmission rate (MVTR) of 5,500 g/m²/24h under standard conditions (23°C, 50% RH). Abrasion resistance follows Martindale method (ISO 12947-2), with the outer fabric enduring 25,000 cycles before noticeable wear, indicating suitability for light industrial use involving occasional contact with surfaces.

Sizing and Fit Considerations

Sizes range from XS to 3XL, with chest measurements increasing in 5cm increments: XS (84cm), S (89cm), M (94cm), L (99cm), XL (104cm), XXL (109cm), 3XL (114cm). Sleeve length is measured from center-back neck to cuff and increases 2.5cm per size (XS: 76cm, 3XL: 91cm). The coat is cut with a 4cm ease at the chest and 6cm ease at the hips to accommodate mid-layer garments while maintaining a streamlined profile. All dimensions are tolerance-controlled to ±1.5cm in accordance with ISO 13688:2013 for protective clothing.

Customization Options

Factory direct procurement allows for adjustments to the DWR treatment concentration (range: 0.8–1.5 g/m²), which affects initial beading angle and wash durability. Closure types can be modified to include water-resistant zippers (YKK AquaGuard® equivalent) or magnetic snaps for specific operational needs. Pocket configurations—such as adding internal secure compartments or radio loops—are adjustable based on workflow requirements. Color options are limited to solid shades achievable through solution dyeing (to minimize batch variation), including navy (Pantone 19-4053), gray (Pantone 14-4105), and olive (Pantone 18-0530), with colorfastness to light rated at 4+ (ISO 105-B02).

Applications in Industrial and Outdoor Work

This coat is suited for environments where workers encounter intermittent light precipitation, mist, or spray—such as agricultural inspection, utility meter reading, or outdoor logistics handling—where full waterproofing is unnecessary but protection against saturation improves comfort and dexterity. The breathable lining prevents excessive heat buildup during moderate activity, while the water-repellent outer layer reduces the conductive heat loss associated with wet fabrics. It is not intended for continuous rain exposure, chemical splash, or high-abrasion industrial tasks requiring certified protective gear (e.g., EN 343 or ANSI/ISEA 107). Procurement teams should assess site-specific conditions, including duration of exposure and layering requirements, to determine suitability.

For technical inquiries, customization requests, or to request a sample batch for evaluation, contact our industrial sales team. Provide details on intended use, required quantities, and any specific performance thresholds to receive a tailored response including lead time, pricing, and compliance documentation.