Factory Direct Navy Rain Coat Women

This navy rain coat is engineered for industrial environments where consistent protection from precipitation and wind is required. Constructed from a 3-layer laminated fabric system, it provides a hydrostatic head rating of 10,000 mm and breathability of 8,000 g/m²/24h, balancing waterproofing with moisture vapor transmission to reduce interior condensation during prolonged wear.

The outer shell utilizes a 100% polyester ripstop weave with a durable water repellent (DWR) finish rated to withstand 20 wash cycles without significant performance degradation. The middle layer is a microporous polyurethane membrane that blocks liquid water while allowing water vapor to escape. The inner lining consists of a brushed polyester mesh designed to wick sweat away from the skin and improve comfort during extended use in temperatures ranging from -5°C to 25°C.

Seams are fully taped using 20mm wide polyurethane tape applied under heat and pressure to achieve a seal strength exceeding 8 N/cm, preventing leakage at stitch points. Zippers are coated nylon coil types with storm flaps and water-resistant zipper pulls, rated for 5,000 cycles of operation. Adjustable cuffs feature hook-and-loop closures with laminated tabs to maintain seal integrity when tightened over gloves or sleeves.

Design Features for Industrial Use

The coat incorporates a detachable insulated liner rated for 100g of synthetic fill, allowing adaptation to varying thermal demands without replacing the outer shell. The liner attaches via heavy-duty nylon snaps rated for 10 kg shear strength, enabling quick installation or removal in field conditions. When detached, the liner compresses to a volume of approximately 1.5 liters for storage.

Ventilation is managed through two underarm zippers with storm flaps, each providing 15 cm of open area when fully deployed. These vents are positioned to align with natural arm movement, minimizing airflow disruption during tasks requiring overhead reach. A two-way front zipper allows bottom-up opening for improved access to tool belts or waist-mounted equipment while maintaining upper-body protection.

The hood is adjustable in three planes—depth, width, and face opening—using laminated cord locks and cord stops designed to resist slippage under vibration. A reinforced brim maintains shape in wind exposure up to 80 km/h, preventing water runoff into the face area. The hood stows into a collar-mounted zippered compartment when not in use, reducing snag hazards.

Material Performance Table

Sizing and Fit Considerations

The coat follows a relaxed industrial fit pattern, providing approximately 10 cm of ease at the chest and 8 cm at the hip to accommodate layering over insulated garments or equipment. Sleeve length is designed with a 2 cm drop shoulder to allow unrestricted movement when reaching forward or upward. Back length measures 78 cm from the base of the neck in size M, with a 2 cm gradient between sizes to maintain proportional coverage.

Available in women’s specific sizes ranging from XS to 3XL, with grading based on ISO 8559-1 anthropometric data for industrial workwear. Each size increment adjusts chest, waist, and hip circumference by 4 cm, while sleeve and back length increase by 1.5 cm. Custom length adjustments are available upon request for specialized applications requiring extended coverage or reduced bulk.

All seams are positioned to avoid high-wear areas, with shoulder seams shifted posteriorly by 1.5 cm to reduce abrasion from backpack straps or harnesses. Side seams are reinforced with double-stitching and bar-tacks at stress points, increasing seam durability by an estimated 40% compared to single-stitch construction.

Quality Assurance Process

Each coat undergoes a three-stage inspection protocol: fabric roll audit upon receipt, in-line checks during assembly, and final functional testing. Fabric rolls are tested for hydrostatic head and DWR performance before cutting, with acceptance criteria set at ±10% of target values. During assembly, seam placement, zipper alignment, and tape adhesion are verified at 10% interval checks.

Finished garments are subjected to a rain tunnel test simulating 100 mm/hour rainfall for 10 minutes, with internal inspection for moisture ingress. Zippers are cycled 50 times under load to confirm storm flap effectiveness. All units are checked for dimensional stability after a single wash cycle at 30°C, with shrinkage limits set at <2% in length and <1.5% in width.

Batch traceability is maintained via barcode-linked records linking raw material lot numbers to finished goods. Random samples from each production batch are retained for 12 months for potential retesting. Non-conforming items are isolated and analyzed to determine root cause, whether material, process, or handling-related.

Packaging and Shipping

Each coat is folded to a standardized dimensions of 30 cm × 40 cm × 5 cm and placed in a 50-micron polyethylene bag labeled with size, color, and batch code. Bags are then packed into export cartons measuring 60 cm × 40 cm × 30 cm, containing 20 units per carton. Cartons are sealed with pressure-sensitive tape and strapped with polypropylene bands for pallet stability.

Cartons are marked with handling symbols indicating “Keep Dry” and “This Side Up” in accordance with ISO 780:2017. For export shipments, cartons are stacked on heat-treated pallets and secured with stretch wrap to prevent shifting during transit. A desiccant packet is included per carton to mitigate moisture accumulation during long-term storage or humid climate transport.

Lead time from order confirmation to shipment is typically 25–30 working days for standard configurations. Expedited production is available upon request, subject to capacity and material availability. Samples can be provided for evaluation, with sample lead times of 7–10 working days and associated costs credited toward subsequent bulk orders.