Women's Rain Jacket Clearance

When selecting rain protection for field operations, the primary concern is consistent waterproof performance under prolonged exposure. This clearance section features women's rain jackets engineered with specific technical attributes that meet industrial durability requirements while accommodating anatomical fit considerations.

Material Construction and Waterproof Rating

The jackets utilize a 3-layer laminate system where the outer layer consists of 100% nylon with a denier rating between 70D and 150D, providing abrasion resistance against rough surfaces and equipment. The middle layer is a microporous polyurethane film rated at 10,000 mm hydrostatic head, measured according to ISO 811 standard, which blocks liquid water penetration while allowing moisture vapor transmission. The inner layer is a tricot polyester mesh that protects the membrane and enhances wear comfort during extended use.

Seam sealing is critical for maintaining waterproof integrity; all seams are taped with 20mm wide polyurethane tape using heat bonding at 180°C, creating a continuous barrier that prevents leakage at stitch points. This construction method ensures the jacket maintains its rated waterproof performance even after repeated flexing and washing cycles, which is essential for personnel working in wet environments such as utility maintenance, landscaping, or outdoor inspections.

Design Features for Functional Use

The jacket includes a storm flap over the front zipper, extending 25mm beyond the zipper teeth on both sides, which prevents water ingress through the closure mechanism during wind-driven rain. The zipper itself is a coil-type YKK AquaGuard with a polyurethane coating, rated for 5,000 cycles without failure, and features a water-repellent finish that reduces surface tension to minimize water absorption.

Adjustability is provided through hook-and-loop cuff straps that allow a 40mm range of tightening to seal against gloves or sleeves, and a hem drawcord with barrel locks that enables circumferential adjustment of up to 60mm to prevent water entry at the waist. The hood is three-panel designed with a wired brim that maintains a 75mm forward extension to shield the face, and it adjusts via dual-side cords and a rear stopper to accommodate hard hats or helmets when required.

Performance Validation and Testing

Each jacket undergoes spray testing per AATCC 35-2019, where it is subjected to 60 liters per hour of water spray at 30 kPa pressure for 5 minutes; acceptable performance requires no more than 1 gram of water penetration on the inner lining. Breathability is assessed using the upright cup method (ASTM E96), with typical moisture vapor transmission rates (MVTR) ranging from 8,000 to 12,000 g/m²/24h, which supports comfort during moderate activity levels in damp conditions.

Durability is evaluated through 20 wash cycles at 40°C followed by tumble drying, after which hydrostatic head and MVTR are retested to ensure performance retention above 80% of initial values. These tests simulate real-world maintenance cycles and help predict service life in industrial laundering environments.

Sizing and Fit Considerations

The women's cut incorporates specific dimensional adjustments compared to unisex or men's models: shoulder width is reduced by 10-15mm, sleeve taper increases by 8mm from bicep to cuff, and waist contouring provides a 20mm suppression at the natural waistline relative to hip measurement. These adjustments improve mobility and reduce excess material that could snag on equipment or impede movement.

Available sizes range from XS to 3XL, with chest measurements spanning 80cm to 120cm and sleeve lengths from 76cm to 88cm, measured from center back neck to wrist. Layering compatibility is designed for a mid-weight fleece or softshell underneath, allowing approximately 25mm of loft space without compromising the jacket’s waterproof integrity or range of motion.

Clearance Inventory Details

Items in this clearance section represent overstock or discontinued color variants from recent production runs, meaning they retain full technical specifications but are offered at reduced pricing due to inventory turnover needs. All jackets are new, unused, and stored in climate-controlled conditions to prevent material degradation.

Color options vary by style but typically include navy, black, olive, and gray, with specific shades dependent on the original production batch. Since these are clearance items, availability is limited to current stock levels, and sizes may not be replenished once depleted. Customers are advised to verify exact measurements against their operational requirements before purchase.

For procurement teams evaluating bulk purchases, these clearance jackets offer a cost-effective solution for equipping personnel with certified rain protection without compromising on core performance metrics. The technical consistency across all units ensures predictable performance in field applications, which simplifies safety planning and equipment standardization.

To inquire about current availability, request a size-specific stock list, or discuss custom labeling options for organizational identification, please contact our industrial sales team. Provide your intended use case and estimated quantity to receive accurate stock confirmation and pricing details.