Long Waterproof Raincoat for Men with Hood

This product page details the technical specifications, material properties, and design considerations for a long-length men's waterproof raincoat with an integrated hood, intended for industrial and professional outdoor use where sustained protection from precipitation is required.

Material Construction and Waterproofing Mechanism

The raincoat utilizes a three-layer laminated fabric system: an outer shell of 100% polyester microfiber with a durable water repellent (DWR) finish, a middle layer of microporous polytetrafluoroethylene (ePTFE) membrane, and an inner lining of brushed polyester for comfort. The ePTFE membrane provides a hydrostatic head rating of 20,000 mm, measured according to ISO 811, indicating resistance to water penetration under sustained pressure. Seams are sealed with polyurethane tape applied via heat bonding to prevent capillary leakage, achieving a seam strength of minimum 15 N/mm as tested per ASTM D751.

Design Features for Industrial Use

The coat extends to mid-calf length (approximately 115 cm for size M) to maximize coverage over trousers and boots, reducing exposure during prolonged outdoor tasks. The hood is integrated into the collar structure with a three-point adjustment system: elastic drawcord at the face opening, vertical adjusters at the temples, and a rear volume adjuster, allowing compatibility with hard hats and hearing protection. Sleeve cuffs feature adjustable hook-and-loop closures with an inner lycra gasket to seal against water ingress, while the storm flap over the front zipper incorporates a drainage channel to direct water away from the closure zone.

Breathability and Moisture Management

Despite its waterproof rating, the garment maintains a moisture vapor transmission rate (MVTR) of 15,000 g/m²/24h as tested per ASTM E96 Procedure B, enabling sweat dissipation during moderate activity. This is achieved through the ePTFE membrane's microporous structure, which blocks liquid water molecules (20 μm diameter) while permitting water vapor passage (0.0004 μm diameter). Pit zips with waterproof zippers are included as standard to enhance ventilation during high-exertion scenarios, increasing effective MVTR by approximately 40% when opened.

Durability and Abrasion Resistance

The outer polyester shell has a tensile strength of 55 N/mm² (warp) and 48 N/mm² (weft) per ISO 13937-2, with a tear strength of 28 N (warp) and 24 N (weft) per ISO 13937-3. Abrasion resistance exceeds 50,000 cycles on the Martindale tester (ISO 12947-2) before noticeable surface degradation, suitable for contact with rough surfaces like scaffolding, concrete, or vegetation. The DWR finish is rated for 20+ wash cycles before reapplication is recommended, maintaining effectiveness per AATCC Test Method 22.

Sizing, Fit, and Layering Compatibility

Available in sizes S through 3XL, the pattern incorporates a 10 cm ease allowance at the chest and 8 cm at the waist to accommodate mid-layer insulation such as fleece or softshell jackets without restricting movement. The back features a dual-vent system with gusseted expansion pleats to allow freedom of motion when bending or reaching, while the articulated elbow design reduces binding during overhead work. Inseam length varies proportionally with size to maintain consistent coverage ratio relative to body height.

Typical Applications in Professional Environments

This raincoat is commonly specified for utility workers, surveyors, construction supervisors, and municipal maintenance crews operating in wet climates where prolonged exposure to rain is expected. Its length and sealed seams provide protection during tasks such as underground utility inspection, roadwork in inclement weather, and outdoor equipment maintenance, where standard-length rainwear may leave lower extremities exposed. The hood's compatibility with headgear makes it suitable for environments requiring simultaneous use of safety helmets and hearing protection.

Quality Control and Testing Protocols

Each batch undergoes hydrostatic head testing on three random samples per 500 units, with acceptance criteria of ≥18,000 mm (allowing for batch variance). Seam seal integrity is verified via dye penetration test per AATCC TM127, requiring zero leakage after 5 minutes of exposure. Dimensional stability is assessed after 5 wash cycles at 40°C per ISO 6330, with shrinkage limited to ≤2% in length and ≤1.5% in width. Final inspection includes verification of all closures, trim attachment strength (minimum 20 N per point), and reflective tape adhesion where applicable.

Customization Options for Project Requirements

While the base model uses charcoal gray outer fabric with black trim, alternative colors are available upon request, including high-visibility yellow (EN ISO 20471 Class 3 compliant) and navy blue, subject to minimum order quantities. Reflective striping can be added to sleeves, shoulders, and back per client specifications, using glass bead or prismatic technology with a minimum retro-reflectivity of 300 cd/lx/m². Logo application via heat transfer or embroidery is feasible on the left chest or upper back, with artwork requirements provided during quotation.

All stated values represent typical performance under standard test conditions. Actual field performance may vary based on exposure duration, temperature extremes, and mechanical stress. For project-specific requirements such as custom lengths, specialized trims, or certification documentation (e.g., REACH, OEKO-TEX® Standard 100), consult technical sales with detailed specifications.

To request a quotation, discuss customization options, or obtain sample evaluation units, contact our technical team using the inquiry form linked below. Provide intended use case, expected quantities, and any required compliance standards to ensure accurate configuration.